ASTM Corten A Weathering Resistant Steel

  • Home
  • ASTM Corten A Weathering Resistant Steel
ASTM Corten A Weathering Resistant Steel

ASTM Corten A Weathering Resistant Steel

ASTM Corten A Weathering Resistant Steel Steel Grade: ASTM Corten A Standard: ASTM Specification: Thickness: 6-420mm Width: 100-4200mm Length: 100-4200mm Hot Forming: Normally it is carried out in a temperature range of 800 °C to 1050 °C. If it is required in different temp

Tel: 0086-371-861#518#27

Mail: [email protected]

ASTM Corten A Weathering Resistant Steel

Steel Grade: ASTM Corten A
Standard: ASTM
Specification:
Thickness: 6-420mm
Width: 100-4200mm
Length: 100-4200mm

Hot Forming: Normally it is carried out in a temperature range of 800 °C to 1050 °C. If it is required in different temperature, it is advisable to carry out a normalizing treatment at the end.
Flame Cutting: Normally it is carried out with the usual methods. In general, no preheat is required, but working on plates with a temperature of less than 10 °C shall be avoided.
Drawing: In spite of its excellent mechanical Properties, Corten A can be moderately drawn.
Welding: Corten A plate can be easily welded using common procedures used for mild steel plate (spot, TIG, MIG, MAG, electrode etc.). It is however advisable to avoid tempering in the heated zone and therefore to limit the ratio of linear energy to the thickness. Considering the chemical composition, it can be stated that Corten A steel is not subject to cold cracking. Welded structures fabricated with corten a steel does not normally need thermal stress relief treatment.
Refercence Standards: Corten A steel plate to be following standards: NFA35-502-E36W, ASTMA242 and A588, EN10155-Fe510A1K1/DD2K1, S.E.W087.

ASTM Corten A Chemical Composition:

Grade

C Max

SI

Mn

S Max

Cr

Ni

Cu

Nb

Nb+V=Ti

P

Corten A

0.12

0.25-0.75

0.20-0.50

0.07-0.15

0.50-1.25

0.65

0.25-0.55

0.25-0.55

-

0.07-0.15

ASTM Corten A Mechanical Properties

Grade

Permissible yield point
ratio

Yield Strength
MPa(min)

Tensile Strength
MPa

Elongation
% (min)

Bend

Corten A

-

345

485

20

1t

Corten A Weathering Steel Parameters:

RECOMMENDED BENDING RADII, WITHOUT SPECIAL REQUIREMNETS

Thickness mm

2-3

4

5

6

7

8

10

12

Radius mm

4

8

10

12

21

24

30

36

ASTM Corten A Application:
The mechanical characteristics and the resistance to atmospheric corrosion make this steel, the best product for the fabrication of agricultural vans and railway wagons, structures of bridges, water pipes, fans, chimneysand boilers.
The material forms its own protective layer when exposed to atmospheric elements. Essentially, the top layer corrodes and then protects the steel beneath it. The natural finish does not normally require any form of maintenance such as painting, which makes the material a highly cost effective alternative to other structural steels.
Mainly used for construction of tanks, containers, bridges, frame structures, vehicles, etc with the request of welded, bolted, etc.

ASTM Corten A Service:
These plates are in a variety of sizes and thicknesses, and are available as ex–stock or directly shipped from the mill. As with all our steels, our plates come with mill test certification, stampings and fully traceable. We can arrange for a variety of tests to be performed on the material if specified.

  • sm520c italy electric spark

    sm520c italy electric spark

    ints for recharging low-battery car. Collect eGO loylty points and redeem them to experience a free day with SPARK car. List of Italian event Pokémon distributions in Generation ...Jun 11, 2019 · This Pokémon was available in Italy from June 23 to 25, 2006. Item: Ability: No

  • en10083 3 34crmos4 steel specification

    en10083 3 34crmos4 steel specification

    EN10083-3 34CrMo4 STEEL PLATE__Steel SupplierEN10083-3 34CrMo4 STEEL PLATE Gangsteel Grade : EN10083-3 34CrMo4 Specification (mm) THK: 3 to 300, Width: 1500 to 4050, Length: 3000 to 27000 Standard: Technical delivery conditions for flat products of high yield strength structural steel EN10083-3 3

  • aisi 1010 valve aisi 1010 flanges aisi 1010 pipe fitting

    aisi 1010 valve aisi 1010 flanges aisi 1010 pipe fitting

    pe fittings and ss 316 flanges from Mumbai. Carbon Steel 1010 Forging | Metal Ministry Inc.AISI 1010 is a low-carbon alloy proper in sheet and strips for profound illustration, carburized and basic applications. Carbon Steel UNS G10100 is perfect for the vehicle business, where it every now and agai

  • construction material 201 28mm stainless steel pipe

    construction material 201 28mm stainless steel pipe

    , jis, and aisi 28mm od stainless steel pipe, as well as from bending, cutting, and moulding 28mm od stainless steel pipe, and whether 28mm od stainless steel pipe is iso, or sgs. 201 stainless steel pipe - kzonsteels.comWuxi Kzon Steel Co., Ltd was established in 2009 ,which is a professional manuf

  • aisi 316 vs aisi 304 and more

    aisi 316 vs aisi 304 and more

    of molybdenum increases corrosion resistance of 316 stainless steel, especially against pitting and crevice corrosion in chloride environments. 304 vs 316 Stainless Steel - The Pros and Cons | Arthur HarrisStainless 304 usually consists of 18% chromium and 8% nickel. Stainless 316 is made up of 16%

  • pdf experimental investigation of emissivity of steel

    pdf experimental investigation of emissivity of steel

    5 μ m has been developed. Experimental Investigation of Emissivity of Steel ...Apr 16, 2013 · In this article, an experimental apparatus for measurements of the emissivity of a metal at different temperatures at \(1.5\, \upmu \text{ m }\) has been developed. Using this apparatus, the

Message information

Please describe your brand size and data volume in detail to facilitate accurate quotation

Copyright @2020 Ezir. All Rights Reserved by HiBootstrap